The purpose of this thesis has been todesign an electric circuit that measurestemperature in three different ways. Asoftware was also designed to record andanalyse the measurments. The result of thecircuit was a PCB with inputs for 42sensors of both surface and non-surfacemeasurments. These all have a maximumerror of ±3°C..

Glass has sophisticated front properties and are used as facades in high buildings. During cold periods, these glass facades could cause thermal discomfort, due to cold downdraught. Cold downdraught can be countered by placing heaters under glass surfaces. Nowadays technology offers highly insulating windows, which is why there is an interest to investigate the indoor climate with only underfloor heating. The research in this area is limited, and few empirical methods are available.

Increased understanding of the mechanisms that operate in conjunction with the welding of metal surfaces may help to improve existing manufacturing processes, and to enable new products and combinations of materials. The purpose of the project has therefore been to acquire a deeper understanding of what is happening in the bond for steel and for the factors that form the basis for a bond to develop between metals in the production of laminates by pressing. The merge has been done by pressing and the surfaces after the experiments have been studied in detail in the scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX) and with interferenceprofilometry in Wyko, to provide a greater understanding of the mechanisms that influence the bonding in the interface between metals. The project was limited to contain the materials Docol 1000, HyTens 1200, Aluminum AA3003 and a commercial steel. The parameters varied in the experiments to study their influence closer are temperature, pressure, heat treatment and pretreatment. This has been implemented by pressing with varying temperature and pressure.

For Skattkärr IF a turf field with warming has been projected to increase field?s utilization hours and to have a longer period for athletes to perform their activities outdoors. The technique chosen to heat the plan is a type of a geothermal heating system without a heat pump. The brine, which is water with 30% ethanol, collects heat from the borehole and discharges it to a coil in the field. There is at position 11 boreholes but it is planned to increase the number to 31, which is the design for the facility.

In this final thesis a rough description of aluminium extrusion is made, the importance of temperature of both the raw material and the extruded profile for a good profile quality. The difficulty in controlling these temperatures are discussed and attempts to increase the control are described. The attempts are basically made by controlling the furnace that is heating the raw material. This is done in a manner that the raw material reaches its final temperature shortly before it is extruded. An IR-camera at the press can be used for profile temperature measurements.

Several studies have analysed the relationship between Normalised DifferenceVegetation Index (NDVI) and radiative Surface temperature. A main goal for moststudies have been to find the best method for carrying out land cover classificationsand to study land cover changes, based on a combination between the twoparameters. Since atmospheric components have a significant influence on bothparameters, most applications were based on multi-temporal data. The quality of theindividual values in such a combination is improved, but the biophysical justificationis uncertain. This study presents a different method, based on only the combination ofvalues that have been registered the same day and about the same time of the day.125 daily images of NDVI and 250 images of radiometric temperature were used inorder to analyse the relationship between (1) NDVI and radiative temperature and (2)NDVI and relative temperature difference between early morning and mid-day.Results between NDVI and radiative temperature show a significant negativecorrelation on areas where a distinct growing season develops, and a strong positivcorrelation where vegetation is abscent throghout the season.

The surface finishing technique called black oxidation is currently being used on thetool holders made of low alloyed tool steel produced by Sandvik Coromant. Blackoxidation isn?t considered a sufficient technique because it doesn?t make the toolholders look like the quality products that they actually are. The reasoning behind thisis that the tool holders can show signs of corrosion after prolonged storing times orin countries with high humidity and temperature. The corrosion doesn?t decrease thetool holders performance, but the customers might believe otherwise.

Aeroseum is an aviation museum located in an old military underground hangar. The ventilation system in the hangar is designed for the military purpose of the hangar. This design includes a solution with air flowing through the space between the construction of the hangar and the rock surface. The solution is intended to avoid a buildup of inflammable gases. This design leads too high humidity levels in the hangar.

Aeroseum is an aviation museum located in an old military underground hangar. The ventilation system in the hangar is designed for the military purpose of the hangar. This design includes a solution with air flowing through the space between the construction of the hangar and the rock surface. The solution is intended to avoid a buildup of inflammable gases. This design leads too high humidity levels in the hangar.

Storage of biomass is often associated with problems such as heat development, dry matter losses and reduction of fuel quality. The rise in temperature can potentially cause a risk of self-ignition in the fuel storage. Moreover, emissions from storage piles can cause health problems in the surrounding. The dry matter losses and reduction of fuel quality can have economical effects. The aim of this thesis project is to develop guidelines on how to store large amount of biomass at Vattenfalls heat and power plants in an optimal way.

ABSTRACTMany wind turbines have problems with icing and there is still no effective method to de-ice without stoppage of production and power loss. Here I therefore consider other methods than those available today, and particularly, I consider how these methods could be applied to wind turbines of the company Oxel. A surface where the water droplets do not attach might be the basis for a useful method. If no water attaches, no ice could form. To accomplish this a hydrophobic surface is nessesary, for example wax.

The aim of the present study was to evaluate the effects of large amounts of straw in the farrowing pen on thermal regulation of the newborn piglet in different weight classes. 20 sows were given 15 kg of straw in the farrowing pen 2 days prior to until 7 days after parturition. A control group of 18 sows had no straw in the pen. 6 litters from each treatment were observed. Measurements of piglet body temperature were made at 0h, 2h, 4h, 8h and 24h after parturition. At ?8h? the body temperature of the piglets in the Straw group were significantly higher (P=0,0149) than the piglets in the Control group.

Atlas Copco Tools develops and manufactures handheld industrial tools. Heat and surface treatments are used to provide the tools with certain properties. There are no routines for the choice of treatment or for how to specify treatment on drawings. Production documents that are sent for production abroad may not be clear enough. Some treatments are known as trademarks and there are no instructions for how to specify these on drawings and in CAD-models.The purpose of this master thesis work is to create recommendations for the procedure of choosing heat and surface treatment.

AbstractConsider a ?uid being heated from below. The heating leads to an upward convectiveforce that is counteracted by the viscous forces of the ?uid. If the convectiveforce is large enough in comparison to the viscous forces the ?uid will be put in anunstable state.

Title in original language: En undersökning av tre olika behandlingsmedels effekt påvegetabiliskt garvat läder för bokbandLanguage of text: SwedishNumber of pages: 32.